A Tubelab SE in a clear Lexan case
A new Tubelab SSE Amp
A Tubelab SE in a clear Lexan case
A new Tubelab SSE Amp
The TSE board shown in this web site is NO LONGER available. There are ZERO in stock, and none will be reordered.
It has been an old faithful for 14 years. Several hundred amps have been built, but all good things must e to an end……..only to be replaced by BETTER things. The filament regulator chip used in the TSE is no longer made….in fact Sharp is no longer alive, it is now part of the Foxconn empire.
The TSE is being redesigned to use a different regulator chip. In the process a list of requests from prior builders was collected and is being acmodated. The new board will be slightly bigger to handle 300B tubes, and provide more space around the heat sinks. More filtering has been added to the filament regulator circuit to handle 2A3’s without issue. I already have a prototype board running, but I expect that it will be 4 to 6 weeks before the design is fully tested and new boards are in stock. The progress of the new TSE-II can be followed on the Tubelab forum here:
There is already a new board in stock, but full web site ready build instructions are not ready yet:
There are also one or two more new boards planned for 2019……stay tuned!
Our new address is:
73 Bottom Ln.
Moundsville, WV 26041
Wele to the new Tubelab website,
We are still testing the new shopping cart experience. ?Until it is up and running, please use the usual method for ordering PC board via email using the instructions on the ordering page. ?New postal rates may apply.
I get far more email than I am currently able to answer. Considerable email asks “how do I order a board”? I have updated the?PC board ordering page?in an effort to reduce these emails. I get a few emails asking technical questions about the PC boards. These will all be answered,
I am building this page on the road somewhere in western Pennsylvania. Sherri and I are staying at her mothers house for a short while. We should be returning to Florida in a week or so.
The munications industry has been hit hard by the economic downturn with hundreds of layoffs in the plant where I work. I am usually at work 10 to 12 hours a day lately doing my best to stay employed. Unfortunately no job is totally secure,
When the economy started to slow down last year, sales of PC boards dwindled too. This forced the delay in the launch of the Tubelab SPP. Fortunately it is nearly ready. For now future products must wait until the current new project (SPP) pays for itself.
There are two P-P designs currently under development. The “Small” one,
The circuitry is not all that unusual. I Have already been informed that it bears a resemblance to SY's "red light district" amplifier, and Morgan Jones "Bevois Valley" amp. The truth is that it is about as simple of a P-P amp that I could e up with that yielded good performance. All three of these amps look like descendants of the Williamson to me.
Why have I done "yet another version of this mon design?" I have breadboarded countless variations of small P-P amps. Some used the 6AQ5 tube, and some used the 6BQ5 / EL84 tube. Every amp was evaluated for performance, simplicity, and most important, the ability to be assembled by builders of varying skill levels and work the first time. One of the main requirements was for a stable design that didn't require any ponent tweaking to make it work. This design worked out to be the best. I chose the 6BQ5 / EL84 tube mostly because that is what was requested in the email that I received. The 6AQ5 is cheaper but produces slightly less power, and a slightly different sound. I may produce a 6AQ5 version of this board if there are enough requests for it.
As usual the board can be wired for triode, UL and pentode mode. Provision for global negative feedback is available. It can be used if needed, and it is needed in pentode mode.
There have been the usual delays due to "trying to keep my day job" activities and Sherri being away for much of the year, but the most recent delays are for two good reasons. I got some $1 output tubes that may work in this amplifier, so I had to try them out. It turns out that a PC board change was required. During the development of the original board I built a hybrid amplifier that used a tube - mosfet "Darlington" connection for the output. Again a PC board change was needed. The changes have been implemented and a prototype board made. The board works as expected with 6BQ5's but I have not tested the other binations yet.
I have included some photos below.
The first board, it hasn't seen any electricity yet.
A careful look will reveal my first problem with this board. The driver tube on the right is installed. The driver tube on the left, won't fit in the socket! The holes for pins 2 and 3 are smaller than the pins on the tube. Next time I'll look more carefully at the sockets before installing them.
It is cranking some tunes here. The flying resistors are the GNFB resistors. I have not yet decided on an optimum value.
I added some much bigger transformers for much bigger sound.
Board on test. Note the distortion number of 0.346%
SY convinced me to try this. The cathode resistors and bypass capacitors have been removed and replaced with LED's. In this case three special LED's were mounted in series on a heat sink material.The amp does indeed sound fantastic with LED's in the cathodes of the output tubes. I am looking for an off the shelf LED that will work here. It may be included in the design.
It can light up the whole room too!
The SPP boards are in house. This one has been kicking out the tunes for a few weeks now.
It has also been the subject of some extensive experimentation. In fact I decided to build another one,
All of the pictures have been taken for the manual and I am currently putting it all together on my laptop while travelling. I have discovered a few photos than must be redone once I return home. We have ordered the parts for a small parts kit which will consist of everything needed to populate the PC board. Both should be ready within two weeks of my return to Florida.
The next step in the “not quite so Simple P-P” is a P-P Driver board. The design goals are simple,
OK, writing down some lofty goals on paper (or in the puter) is easy. Building the circuit and getting it to work is not. This project has been alive since before there was a Tubelab web site. In many ways it has evolved from my 300Beast amplifier. It incorporates a lot of the 300Beast design and many techniques that I have learned since the 300Beast was built.
I laid out this prototype PC board in a hospital waiting room in Pittsburgh during the Christmas (2008) holidays. I started building it when I got back to Florida. When I pleted it and powered it up I found that I had swapped the top and bottom layers when making the board, resulting in a mirror image of what I laid out. After nearly tossing it in the trash, I realized that all I needed to do was solder a set of tube sockets on the back of the board. The board is alive and working now. More details are on the Universal Driver Board page.
I have received numerous requests for an amplifier using all octal tubes. Octal tubes use up more board space than miniature tubes and are usually more expensive,
See the Octal Driver Board page for more details.
I have developed another future product,
I got a lot of email about the MiniTron. Some called it cool,
The MiniTron amplifier was designed for entry into the Circuit Cellar / Microchip design contest. In a sea of microprocessor powered IC based gizmos this vacuum tube amplifier WON ONE OF THE CATEGORY PRIZES!!! It is featured in the Oct 2009 issue of Circuit Cellar magazine, and is currently on their web site.I will be posting much more information about this design in the ing months. You don't care anything about an amplifier that has more chips than tubes? I don't blame you, but this project has taught me a lot about the distortion producing mechanisms in vacuum tube circuits. I am using this information to design some radically new vacuum tube circuitry, that is silicon free, as well as some unique hybrid designs. Unfortunately the events outlined below have severely slowed down the progress. The amplifier you see above was pleted in early October, and hasn't been touched since.
Progress has resumed slowly with the design of an all tube cathode follower amp incorporating some of the technology developed during the development of the MiniTron. A new page for this design will be created soon. One ponent of the MiniTron is the cathode follower amplifier, which still has its own page. The plete contest submission including schematics, source code, and design details can be found here: